X-ray damage characterization in BaLiF3,KMgF3 and LiCaAlF6 complex fluorides

Two-inch sized KMgF₃,BaLiF₃ and LiCaAlF₆ (LiCAF) single crystals were grown by the Czochralski method under a CF₄ atmosphere. X-ray irradiation was used to carry out a comparative study of induced optical absorption phenomena and colour centre creation in the ultra-violet and visible spectral regions. The integral of the induced absorption spectra is significantly lower in LiCAF with respect to the other studied materials. It is found that the amplitude of the F-absorption band is suppressed more than a factor of 3 by Mg-doping. For Mg-doped crystals, the optimum doping concentration is about 0.2 mol% of Mg²⁺.     

Dispersion Characteristics of Waveguide Arrays in Optical Spectrum Analyzers

Formulas for calculating the spectral characteristics of waveguide arrays, which are incorporated into waveguide spectrum analyzers based on planar waveguides, channel waveguides, and fiber optical waveguides, are derived taking into account the contribution of both the waveguide dispersion and the material dispersion to the dispersion factor. These formulas are used to study the dependence of the dispersion factor on the waveguide-system parameters for specific models of waveguide arrays. It is shown that consideration of contributions of the waveguide dispersion and material dispersion can affect profoundly the spectral characteristics of waveguide arrays.     

Measurement uncertainty of selenium determination in the reference material Seronorm Trace Elements Serum by hydride generation atomic fluorescence spectrometry

 An analytical result is not considered to be complete without a statement of the measurement uncertainty associated with it. Evaluation of measurement uncertainty is therefore an essential part of every determination. In the present study the measurement uncertainty of the result of determination of selenium in the reference material Seronorm Trace Elements Serum was studied. The combination of a digestion procedure using sulfuric acid, V₂O₅ in H₂SO₄ and hydrogen peroxide and the continuous flow approach of hydride generation atomic fluorescence spectrometry (HG-AFS) detection was used for selenium determination. The total uncertainty budget was calculated with the help of the GUM Workbench program, in which computations follow the rules of the ’ISO guide to the expression of uncertainty in measurement’. The major sources of uncertainty were found to be due to the recovery of the procedure, measurement of peak heights and the purity of Na₂SeO₃. A selenium mass fraction of 77.1±4.8 ng/g (with a coverage factor of 2.1, 95% probability) was determined, which is comparable with the recommended value of 80 ng/g. Received: 13 September 2002 Accepted: 23 December 2002 Acknowledgements We would like to thank Tinkara Buˇcar, B.Sc. for useful discussions and the IAEA Vienna, for financial support of the project 11553/RO. Presented at CERMM-3, Central European Reference Materials and Measurements Conference: The function of reference materials in the measurement process, May 30–June 1, 2002, Rogaška Slatina, Slovenia Correspondence to V. Stibilj     

基于累积损伤过程的不完全预防维护决策

基于累积损伤过程研究旧系统的不完全预防维护策略,冲击服从非时齐Poisson过程,并产生随机的损伤量,损伤量是加法累加的.系统在累积损伤量达到k或系统运行年龄达到T时进行计划内预防维护.在两次计划内预防维护之间,当累积损伤量达到预定水平K (k K)时,对系统进行计划外维护,其费用高于计划内预防维护,利用再生过程理论得到单位时间维护成本,讨论在时齐Poisson过程下的时间预防维护策略与水平预防维护策略,同时给出算例.     

On the dynamic electromechanical loading of dielectric elastomer membranes

Dielectric elastomer actuators (DEAs) have received considerable attention recently due to large voltage-induced strains, which can be over 100%. Previously, a large deformation quasi-static model that describes the out-of-plane deformations of clamped diaphragms was derived. The numerical model results compare well with quasi-static experimental results for the same configuration. With relevance to dynamic applications, the time-varying response of initially planar dielectric elastomer membranes configured for out-of-plane deformations has not been reported until now. In this paper, an experimental investigation and analysis of the dynamic response of a dielectric elastomer membrane is reported. The experiments were conducted with prestretched DEAs fabricated from 0.5 mm thick polyacrylate films and carbon grease electrodes. The experiments covered the electromechanical spectrum by investigating membrane response due to (i) a time-varying voltage input and (ii) a time-varying pressure input, resulting in a combined electromechanical loading state in both cases. For the time-varying voltage experiments, the membrane had a prestretch of three and was passively inflated to various predetermined states, and then actuated. The pole strains incurred during the inflation were as high as 25.6%, corresponding to slightly less than a hemispherical state. On actuation, the membrane would inflate further, causing a maximum additional strain of 9.5%. For the time-varying pressure experiments, the prestretched membrane was inflated and deflated mechanically while a constant voltage was applied. The membrane was cycled between various predetermined inflation states, the largest of which was nearly hemispherical, which with an applied constant voltage of 3 kV corresponded to a maximum polar strain of 28%. The results from these experiments reveal that the response of the membrane is a departure from the classical dynamic response of continuum membrane structures. The dynamic response of the membrane is that of a damped system with specific deformation shapes reminiscent of the classical membrane mode shapes but without same-phase oscillation, that is to say all parts of the system do not pass through the equilibrium configuration at the same time. Of particular interest is the ability to excite these deformations through a varying electrical load at constant mechanical pressure.     

Synthesis and optical properties of tetraphenylmethane-based tetrahedral fluorescent compounds and their water-soluble PEG-linked polymers

The synthesis and optical properties of tetrahedral fluorescent compounds comprising of tetraphenylmethane as the core and oligothiophenes as the chromophoric arms, and their water-soluble poly(ethylene glycol)-linked polymers are reported.     

Structural and electrical properties of crystalline (1−x)Ta2O5−xTiO2 thin films fabricated by metalorganic decomposition

Polycrystalline (1−x)Ta₂O₅−xTiO₂ thin films were formed on Si by metalorganic decomposition (MOD) and annealed at various temperatures. As-deposited films were in the amorphous state and were completely transformed to crystalline after annealing above 600 °C. During crystallization, a thin interfacial SiO₂ layer was formed at the (1−x)Ta₂O₅−xTiO₂/Si interface. Thin films with 0.92Ta₂O₅–0.08TiO₂ composition exhibited superior insulating properties. The measured dielectric constant and dissipation factor at 1 MHz were 9 and 0.015, respectively, for films annealed at 900 °C. The interface trap density was 2.5×10¹¹ cm⁻² eV⁻¹, and flatband voltage was −0.38 V. A charge storage density of 22.8 fC/μm² was obtained at an applied electric field of 3 MV/cm. The leakage current density was lower than 4×10⁻⁹ A/cm² up to an applied electric field of 6 MV/cm.     

Mössbauer study on LiFePO4 cathode material for lithium ion batteries

Crystalline LiFePO₄ has been synthesized using solid-state, spray pyrolysis, and wet chemical methods. The crystal parameters were obtained from Rietveld’s refinement methods of the X-ray diffraction patterns. A detailed investigation of the Fe valency carried out using Mössbauer spectroscopy at room temperature indicates that Fe is predominantly present in its bivalent state.     

Numerical analysis of a model of cure process for composites

We consider a composite material composed of fibres included in a resin which becomes solid when it is heated up (reaction of reticulation). The mathematical modelling of the cure process is given by a kinetic equation describing the evolution of the reaction of reticulation coupled with the heat equation. In this paper, we are interested in the computation of approximate solutions. We propose a family of discretized problems depending on two parameters (β₁, β₂) ε [0, 1]² which split the linear and non‐ linear terms in implicit and explicit parts. We prove the stability and convergence of the discretization for any (β₁, β₂) ε [½, 1 ] × [0, 1]. We present also some numerical results. Copyright © 2006 John Wiley & Sons, Ltd.     

聚合物纳米孔隙增透膜制备工艺的研究

论述了聚合物纳米孔隙增透膜的制备工艺流程,分析了聚合物材料分子量、实验环境温度和湿度、溶剂挥发性等条件对纳米孔隙增透膜的影响。研究表明,聚合物材料分子量的增大、温度的降低、湿度的升高以及采用挥发性弱的溶剂都将导致增透膜孔隙尺寸的增大,孔隙越大其对光的散射损耗就会增大,所以增透膜的透过率就越低。通过大量的试验分析得出一组较理想的工艺参量:使用低分子量的聚合物材料(小于15 kg/mol),环境温度大于25℃、环境相对湿度小于30%,在采用低沸点的溶剂如四氢呋喃等措施下可有效降低增透膜散射损耗。